Mains Powered UltraDIAL 4G GSM Shed Alarm Kit

Mains Powered UltraDIAL 4G Shed Alarm Kit 2, designed to help protect your Shed, Garage or Workshop, when triggered it will activate up to 4 Sirens (including an external solar powered siren) together with secretly contacting key-holders by Phone & Text.

Supplied with:

• 1 x 4G UltraDIAL Alarm Control Panel (designed to silently contact owners by Phone & Text if triggered).
• 1 x Wireless BT PIR (with a built in Siren).
• 1 x Magnetic Door Contact with built in Vibration Sensor and Keypad (built in Siren which can be silenced if required). 
• 1 x External Wireless Siren (this can be positioned up to 50 metres away).
• 1 x Internal Wireless Siren,
• 2 x Remote Controls (designed to Arm & Disarm the complete Alarm System).
• 1 x Shed Alarm Warning Window Sticker.
• 1 x 3-pin Plug in Transformer.

How it Works:

The 4G UltraDIAL, Wireless Door Contact, PIR & Sirens are all connected to each other within a unique and secure Wireless Network and are all Armed and Disarmed at the same time by using either of the Remote Controls supplied.

We would recommend hiding the UltraDIAL out of sight or in a very hard to reach position, this is easy to do as it is Wireless & Fully Weatherproof although this kit does need access to a standard wall socket as it is supplied with a Plug in Power Supply.

If the Alarm is activated the UltraDIAL will silently contact up to 3 x key-holders by Phone & Text message whilst the Sirens built into the PIR & Door Contact will activate at the same time as the Internal & External Sirens, meaning the Intruder will hear 4 Sirens from different locations without even knowing that the Alarm is also contacting the owners.

Solar Siren:

The Solar Siren is weatherproof and has a built in tamper switch, it can be used in 2 ways:

• Solar Siren: when mounted in a location open to daylight, it can be used with its built in re-chargeable Lithium Battery, which is charged & maintained by the built in Solar Siren.  
• Battery Siren: when used in a very sheltered location with minimal access to daylight, it can be used with standard AA Batteries, but the batteries would have to be replaced more often (9 - 12 months normal use). 

BT PIR:

The battery powered PIR (007-0200) supplied has a built in 130 Decibel Siren, with a 30 second Exit Delay & 5 second Entry Delay. Its detection range is 8 metres with a horizontal coverage of 120 degrees and vertical of 90 degrees.

BT Wireless Vibration & Magnetic Door or Window Contact:

It has a host of features including:

• Optional Vibration Sensor (with adjustable sensitivity settings).
• Optional Magnetic Contact operation.
• Built in Keypad (can be used to Arm & Disarm).
• Can be Armed & Disarmed by the Remote Controls in the kits.
• Optional built in 130 decibel Siren (can be turned off) operates for 30 seconds.
• Optional Door left Open 'Beep' mode (whilst in disarm mode). 
• Optional Door left Open 'Alarm' mode (whilst in Armed state).
• Easy to Fit Magnet.
• It can also be used as a stand-alone Alarm.

You can choose to use the device with Vibration Only, Magnetic Contact Only or with both Enabled.

When used as a Magnetic Contact on a Window or Door, one part would be fitted onto the Door/Window and the other part onto the Frame (in such a position that when closed both parts are nearly touching).

Keypad:

The device has a small keypad that is used to carry out the choice of commands to suit your application together with being able to Arm & Disarm the complete Alarm system in the event you have forgot to carry the relevant Remote Control.

Wireless Siren:

The Wireless Siren is powered by 2 x AA batteries and have an operating range of around 100 metres (line of sight), which equates to approximately 50 metres in most applications.

A unique and flexible 4G Wireless Garage Alarm Kit !!

Communication:

The Alarm communicates via the mobile phone networks (nano sim card required), it will contact up to three key-holders by Telephone (with your own pre-recorded message) & Text Message when activated.

We do offer two Roaming SIM Cards from a third party supplier (at cost) designed for use in Alarms & Tracker Systems, these are low level contract sim cards (working on a direct debit) operating over all the major UK Networks ensuring your Alarm has the best signal available in all locations. 

These can be selected within the drop down options near the Add to Card Button.

The two options are our 20 Plan (click here) & 50 Plan (click here), please click the links to read all about them.

You can also purchase the product with no sim card and simply use your preferred supplier (many options are available).

Additional Detectors & Sirens:

If you want to expand the Alarm, you can add the additional Detectors to it as shown below:

• Wireless Door Contacts (007-0260) & (007-1460).
• Pressure Mat (007-0640).
• Indoor Battery Siren (007-0230).
• Outdoor Solar or Battery Siren & Strobe (007-0221).
• Standard PIR (007-0200).
• Standard PIR with Hood (007-1410).

Additional Buildings:

The wireless operating range of 100 metres (line of sight) between the accessories and the UltraDIAL equates to around 40 - 50 metres in many applications, which allows various buildings to be protected at the same time, many customers will cover two, three or even four buildings with this Alarm. 

Arming & Disarming:

The Alarms are Armed & Disarmed by using the Remote Controls (supplied) from up to 100 metres away, up to 9 Remote Controls can be used with each Alarm. 
If the UltraDIAL Alarm is powered by the external 5v power source, then it is possible to Arm & Disarm the Alarm via SMS (text message).There is a 30 second Exit Delay built into the Alarm for easy use.

Contacting Key-holders:

The Alarm will contact between 1 & 3 key-holders (depending on how you have chosen to program the alarm) by Telephone & SMS (either can be turned off whilst programming the alarm) when activated.

It will normally take take between 30 - 60 seconds to call the first key-holder when powered by battery, and quicker when powered by a plug in transformer or usb cable (this can vary depending on the mobile phone networks at the time).  

Recording Message:

You can record a 30 second message into the Alarm, which will be replayed to the key-holders when the Alarm calls them.

Power Supply:

This UltraDIAL Alarm is supplied with a Plug in 5v DC Power Supply and 3 x Lithium AA Batteries (which act as a battery back-up in the event of a power cut).

Receiving a Call:

When the Alarm calls the key-holders, there is the choice to:

• Listen to your pre-recorded message and do nothing (the alarm will contact the other key-holders).
• Listen to your pre-recorded message and press # on your telephone (this will disarm the UltraDial and prevent it from calling further key-holders).
• Listen to your pre-recorded message and press * on your telephone (this will prevent it from calling further key-holders, but keep the Alarm fully armed (ready for further activations).

Wired Alarm Detectors:

The UltraDIAL has one momentary volt free Inputs, 1 x N/O or N/C, these can be used with many types of devices, examples listed below:

Normally Open going Closed:

• Water & Flood Sensors.
• Alarm Panel.
• Perimeter Beam.
• Pressure Mat.
• Tilt Switch.

Normally Closed going Open:

• Door Contact.
• Gate Contact.
• Alarm Panel.
• Pressure Mat.
• Tilt Switch.

Easy Programming:

The UltraDIAL is very easy to program, probably the easiest GSM Alarm to program on the market today by using the small built in keypad, following some very simple instructions.

Weatherproof:

The UltraDIAL is fully weatherproof and rated at IP66, so can be used in most locations, it is not however designed to be submerged.

Low Battery:

The UltraDIAL Alarm will send the primary key-holder a SMS (text message) if the batteries are getting low when being used on battery power only .

Status Report:

A status report can be obtained by sending the device a Text Message.

Mains Power Failure:

When the Alarm is being powered by an external 5v power supply, it will send the primary key-holder a SMS (text message) in the event of a Power Cut together with another when the power comes back on (provided you also have batteries fitted).  

Security Screws:

The lid is fitted with 4 x security screws and a tool is supplied as standard.

The UltraDIAL is a unique & versatile Battery GSM Alarm that can be used in many types of applications:

This is a very versatile Security device ideal for many applications designed by Ultra Secure Direct.

If you need advice, please Contact Us !!

• 1 x 4G UltraDIAL Alarm (with Lithium AA Batteries).
• 2 x Remote Controls.
• 1 x Internal Wireless Siren (with batteries).
• 1 x Outdoor Solar Wireless Siren.
• 1 x BT PIR (with Siren).
• 1 x Magnetic Door Contact with Vibration Sensor, Siren & Keypad (007-0630).
• 1 x 2-pin Plug in Transformer.
• 1 x Shed Alarmed Window Sticker.

UltraDIAL:

• Battery Power: 3 x Lithium AA Batteries (supplied).
• Battery Life: 6 months in most applications).
• Main Power: Yes (optional 5v DC plug in transformer).
• Programming Method: Easy Built in Keypad.
• Operates on 4G, 3G & 2G Networks.
• Wireless Transmission Range: 300 ft.
• Size: 6 1/4" x 3 1/4" x 1 3/4".
• Colour: Black.
• Wired Inputs: Yes (1 x Volt Free N/O or N/C).
• Cable Entry: 2 x Glands.
• Wireless Inputs: Yes (Wireless PIR's & Door Contacts).
• Wireless Outputs: Yes (Internal & External Sirens, PIR's).
• SIM Card Required: Yes (nano size).
• Calls Key-holders: Yes (maximum of three, which can be turned off).
• Sends Key-holders SMS: Yes (maximum of three, which can be turned off).
• Built in Siren: No (designed as a covert alarm).
• Mounting Method: 2 x Screw Holes in Flange.
• Weatherproof: Yes (IP66).
• Arming & Disarming Method: Remote Control, Keypad, Receiving A Call.
• Remote Operation on Battery: Yes (# to Disarm, * to Stop & Remain Armed).
• Remote Operation on Mains:  Yes (# to Disarm, * to Stop & Remain Armed, SMS to Arm, SMS to Disarm).
• Power Failure Notification: Yes (when used with a plug in transformer).
• Weekly Status Report: Yes (can be turned off).
• Low Battery Notification: Yes (to primary key-holder).
• Recording Message: Yes (this will be replayed to the key-holders when the alarm calls them).
• Frequencies:
• LTE-TDD B38/B40/B41.
• LTE FDD B1/B3/B5/B7/B8/B20/B28.
• UMTS/HSPA+ B1/B8.
• GSM/GPRS/EDGE 900/1800 MHz.

PIR:

• Alarm Detection Type: PIR (passive infrared detector).
• Hood: Yes (rubber).
• Arming & Disarming Method: Remote Control.
• Working Distance between PIR & Remote Control: 300 ft (line of sight).
• Transmission Distance to additional Wireless Sirens: 300 ft (line of sight).
• Built in Siren: Yes (130 decibels).
• Exit Delay: Yes (30 seconds).
• Entry Delay: Yes (5 seconds).
• Siren Duration: 60 seconds (remains fully armed, until disarmed by remote control).
• Detection Range: 24 ft.
• Detection Horizontal Coverage: 120 Degrees (with front of hood fully opened up).
• Detection Vertical Detection: 90 Degrees (with front of hood fully opened up).
• PIR Power Supply: 3 x AA Batteries (supplied).
• Remote Control Power Supply: 1 x 3v Lithium Coin Battery.
• Size of PIR: 2 3/4" x 4 1/4" x 1 1/2".
• Size of Remote Control: 3" x 1 3/4" x 1/2".
• PIR Battery Life: 12 - 18 months (normal use).
• Warranty: 1 Year.

Vibration Sensor:

• Wireless Operation with UltraDIAL Alarms: Yes.
• Wireless Operation with BT PIR Alarms: Yes.
• Wireless Range: 300 ft (line of sight).
• Internal Siren: Yes 130 Decibel (optional, can be turned ON or OFF).
• Vibration Sensor: Yes (optional). 
• Magnetic Contact: Yes (optional).
• Vibration Sensitivity Adjustment: Yes (low, medium & high).
• Duration of Siren: 30 seconds. 
• Keypad Code Change: Yes (cannot start with 3).
• Keypad To Arm: Yes (press 3). 
• Keypad To Disarm: Yes (code + 3).
• Exit Delay: 20 seconds.
• Entry Delay: 5 seconds.
• Change Code Option: Yes.
• Size of Contact: 21/4" x 1 1/2" x 5/8".
• Size of Magnet: 1 3/4" x 1/2" x 1/2".
• Power Supply: Battery (1 x 3v Lithium CR2 Battery).  
• Colour: White.
• Open Door Beep: Yes Optional (when disarmed).
• Open Door Siren: Yes Optional (when armed).
• Test Mode: Yes (beep on open & close with 30 second reset.
• Stand-alone Operation: Yes.
• Frequency to Wireless Sirens 868 Mhz.

1B Beams:

• Beam Size: 13 1/4" x 5" x 2".
• Output Type: Momentary N/O or N/C.
• Cable Length: 30" (2-core).
• Power Supply: Re-chargeable AA Batteries.
• Charging Method: Built in Solar Panels.
• Mounting Methods: Wall or Pole.
• Detection Range: 300 ft.
• Wireless Transmission Range: 2700 ft (line of sight) if used with different accessories.
• Frequency: 433 Mhz.
• IP Rating: (IP66)
• Distance Between Detection Beams: 2 1/4".
• Number of Beams: 1 set.
• Charging Port: 9 - 12v DC (500 m/A to 1 amp).

Solar Siren:

• Built in Siren: 130 Decibel.
• Siren Duration: 3 minutes.
• Built in Flashing Strobe: Rapid (activation).
• Power Supply: 1 x Built in 3.7v / 450 mA Lithium Battery (supplied).
• Optional Battery: 4 x Alkaline AA Batteries (for low level light locations).
• Battery Life of Alkaline Batteries: 9 - 12 months low light applications (normal use).
• Weatherproof: Yes (IP-65).
• Anti-Tamper Switch: Yes.
• Line of Sight Wireless Range: 300 ft (line of sight).
• Size: 4 1/4" x 6 3/4" x 1 1/8".
• Warranty: 1 year. 

Wireless Indoor Siren:

• Built in Siren: Yes (130 Decibel).
• Power Supply: 2 x AA Batteries.
• Wireless Range: 300 ft (line of sight).
• Size: 2 1/2" x 3 3/8" x 7/8".
• Colour: Cream.
• Siren Duration: 60 seconds (but remains fully armed).

Remote Controls:

• Power Supply: 1 x 3v Lithium Coin Battery.
• Wireless Range: 300 ft (line of sight).
• Operation Option: Arm or Disarm.
• Size: 3" x 1 3/4" x 1/2".
• Battery Life: 1- 2 Years (normal use).
• Warranty: 1 Year.

Shed Sticker:

• Self-Adhesive on the front of the label designed to fit inside a window.
• Size: 3 1/8” x 2 3/8”.
• Colour: Red Print on White Background.
• Wording: This Shed is Alarmed.